The Essential Guide to Toyota HiAce 11 Seater Wiper (2004-2018)

The Toyota HiAce 11 Seater is a rugged and reliable people carrier that has been a popular choice for families and businesses alike since its introduction in 2004. Over the years, the HiAce has undergone several updates and revisions, but one component that has remained largely unchanged is the wiper system.

This article will provide a comprehensive guide to the Toyota HiAce 11 Seater wiper (2004-2018), covering everything from basic maintenance to troubleshooting and replacement.

 Basic Maintenance

Replacing the Wiper Blades:

 Lift the wiper arm away from the windshield.
 Pinch the clips holding the old blade in place and slide it off the arm.
 Align the new blade with the arm and slide it on until it clicks into place.

Cleaning the Windshield:

 Use a clean microfiber cloth to wipe down the windshield.
 Apply a glass cleaner to the cloth and wipe the windshield again to remove any dirt or debris.

Checking the Wiper Fluid:

 Open the hood and locate the windshield washer fluid reservoir.
 Check the fluid level and top it off with a mixture of washer fluid and water if necessary.

 Troubleshooting

Wiper Blades Not Wiping Properly:

 Check the wiper blades for wear or damage.
 Clean the windshield with a glass cleaner.
 Adjust the wiper arms to ensure they are making good contact with the windshield.

Wiper Motor Not Working:

 Check the wiper fuse and relay for blown or damaged components.
 Disconnect the electrical connector to the wiper motor and check for loose or damaged connections.
 Test the wiper motor by applying power directly to it.

 Replacement

Required Parts:

 New Wiper Motor
 New Wiper Linkage
 New Wiper Blades

Steps:

1. Disconnect the Battery:

 Disconnect the negative battery terminal to prevent any electrical shorts.

2. Remove the Cowl Panel:

 Unclip the plastic cowl panel from the base of the windshield.
 Lift the panel off and set it aside.

3. Remove the Wiper Arms:

 Lift the wiper arms away from the windshield and remove the nuts holding them in place.
 Pull the wiper arms off the transmission linkage.

4. Remove the Wiper Motor:

 Disconnect the electrical connector to the wiper motor.
 Remove the bolts holding the wiper motor in place.
 Lift the wiper motor out of the vehicle.

5. Install the New Wiper Motor:

 Place the new wiper motor into the vehicle and secure it with the bolts.
 Connect the electrical connector to the wiper motor.

6. Install the New Wiper Linkage:

 Connect the new wiper linkage to the wiper arms.
 Secure the wiper arms to the transmission linkage with the nuts.

7. Install the New Wiper Blades:

 Slide the new wiper blades onto the wiper arms until they click into place.

8. Reconnect the Battery:

 Reconnect the negative battery terminal to restore power.

 Conclusion

The Toyota HiAce 11 Seater wiper is a critical component for ensuring clear visibility during rain and snow. By following the maintenance, troubleshooting, and replacement tips outlined in this guide, you can keep your HiAce's wiper system functioning optimally for years to come.
Serial Number: 88085517

Toyota HiAce 11 Seater Wiper (2004-2018): A Comprehensive Guide

Introduction

The Toyota HiAce is a popular commercial van known for its reliability, durability, and spacious interior. First introduced in 1967, the HiAce has undergone several revisions and upgrades over the years, with the fifth generation being produced from 2004 to 2018. This article will focus specifically on the wiper system of the Toyota HiAce 11 Seater from this generation.

Windshield Wipers

The Toyota HiAce 11 Seater is equipped with a pair of conventional windshield wipers that are parallel to each other. These wipers are activated by a lever on the steering column and can be set to operate at different speeds, including intermittent, low, and high. The wipers come with replaceable wiper blades that can be easily replaced when worn out.

Rear Window Wiper

In addition to the windshield wipers, the HiAce 11 Seater also features a rear window wiper. This wiper is located on the rear door and is activated by a separate lever on the dashboard. The rear wiper operates at a single speed and is essential for maintaining visibility when driving in wet conditions.

Wiper Fluid System

The Toyota HiAce 11 Seater has a wiper fluid reservoir located under the hood. This reservoir holds a solution of water and wiper fluid that is used to clean the windshield and rear window. The wiper fluid is dispensed through nozzles located at the base of the windshield and rear door.

Wiper Motor

The wiper motor is responsible for powering the wiper blades and moving them across the windshield and rear window. The wiper motor is located under the dashboard and is connected to the wiper linkage.

Wiper Linkage

The wiper linkage is a system of rods and levers that connect the wiper motor to the wiper blades. The linkage transfers the motion of the wiper motor to the wiper blades, causing them to move in a sweeping motion across the glass.

Wiper Troubleshooting

If you encounter any problems with the wiper system on your Toyota HiAce 11 Seater, there are a few common issues to check:

 Blown fuse: A blown fuse can prevent the wiper motor from receiving power. Check the fuse box and replace any blown fuses.
 Faulty wiper motor: A faulty wiper motor will not be able to power the wiper blades. You will need to replace the wiper motor if it is faulty.
 Damaged wiper linkage: A damaged wiper linkage can cause the wiper blades to move improperly or not at all. Inspect the linkage for any damage and replace it if necessary.
 Worn-out wiper blades: Worn-out wiper blades will not be able to effectively clean the windshield or rear window. Replace the wiper blades regularly to ensure proper visibility.
 Low wiper fluid level: A low wiper fluid level can prevent the nozzles from dispensing fluid onto the windshield or rear window. Fill up the wiper fluid reservoir and clean the nozzles if necessary.

The wiper system on the Toyota HiAce 11 Seater is an essential component for maintaining visibility in wet conditions. Regular maintenance and troubleshooting can help ensure that the wiper system is functioning properly and providing optimal visibility.